Gallade Chemical - Chemical Distributor
>> ABOUT US   >> CONTACT US   >> CAREERS
>> HELP   >> SDS   >> CERTIFICATE OF ANALYSIS
PLATING
Navigate:  Store Home / Chemicals for Special Applications / Plating / MICCROSHIELD STOP-OFF LACQUER 5 Gal Can
<   Previous Product
Next Product   >
Product   Gallade Part#   Price    

MICCROSHIELD STOP-OFF LACQUER 5 Gal Can

L59010
$0.00
Add To Cart

MICCROSHIELD STOP-OFF LACQUER 5 Gal Can MAIN

MICCROSHIELD is a high-solids, air-dry lacquer, transparent orange/red in color, that can be applied by brushing, dipping or spraying if diluted properly.

MICCROSHIELD is suitable for masking in the following cycles:
Electropolishing;  Electroless Nickel;  Neutral and Acid Gold Palladium;  Indium Rhodium;  Anodizing Bronze; Any Acid Cycle Silver; Chrome.

APPLICATION PROCEDURE

1. Chemically and/or mechanically clean the area of the part to be masked. The area to be masked must be free of all dirt, grease, oil or other contaminants. Cleaning is the most critical aspect of the masking process.

Apply MICCROSHIELD to the area to be masked by dipping, brushing, or spraying.  Appropriate dilution of MICCROSHIELD is required for spraying. For reducing MICCROSHIELD use MICCROSHIELD REDUCER only!

Apply a minimum of 2 successive coats of MICCROSHIELD to the area to be masked, allowing a minimum of 30 minutes air-dry time between coats and overnight air-dry time after final coat before introduction into solution. Faster drying of MICCROSHIELD can be accomplished by force-drying for 15 minutes in an oven not exceeding 140_ F, or over a hot plate not exceeding 140_ F. Drying time will vary depending on relative humidity. Make sure MICCROSHIELD has lost all solvent odor before force drying or applying additional coats. Drying over a hot plate is preferable to oven drying.

4. For extra long cycles, 3 coats are recommended. If area to be masked is highly polished, see back page for additional application procedures.

5. MICCROSHIELD can be removed using MICCROSTRIP B or MICCROSTRIP A.  MICCROSHIELD REDUCER is also effective but somewhat slower.

6. Replace evaporated solvent with MICCROSHIELD REDUCER ONLY!

COLOR: Transparent Orange/Red  

CHARACTERISTICS

WT./GAL.: 7.9#
VISCOSITY: 45-50 sec. #2 Zahn FLASH POINT: 30_ F, T.C.C.
COVERAGE RATE: Approx. 510 ft2 (47.4m2) per gallon, 1.1 mil dry film
MICCROSHIELD is available in: 1 gal., 5 gal., and 55 gal. containers.

PRECAUTIONARY INFORMATION

CONTAINS VOLATILE SOLVENTS_Keep away from sparks and open flame. Keep container closed when not in use. Store at temperatures above 32_F and below 1 05_F. Maintain adequate ventilation in working area. Wear approved respirators and protective clothing when working in confined areas. Avoid repeated breating of concentrated vapors. Prolonged contact of liquid material with the skin may be irritating. In case of skin contact, wash exposed skin surface thoroughly with soap and water. In case of eye contact, flush eyes thoroughly with water for 15 minutes and consult a physician. Refer to MATERIAL SAFETY DATA SHEET for further infommation.



CUSTOMER QUESTIONS
There are currently no questions about this product.
Ask a Question


714 546 9901 x124
Returning Customer?
Shipping Policy Return Policy
Shopping Cart
 

The Shopping Cart is currently empty


Purchasing Guidelines Chemicals

Must be a commercial business shipping to U.S. business address
* No individuals
* No International

Include chemical use/application in order comments
Orders failing to meet these guidelines will be cancelled