MICCRO XP-2000 is a butyl rubber compound suitable for use in:
Electroless Nickel Plating
Chemical Milling
Hard Coat Anodizing
Acid Solutions in General
APPLICATION PROCEDURE
1. XP-2000 should be stirred prior to usage and periodically if not used for extended periods of time.
2. Chemically and/or mechanically clean the area of the part to be masked. The area to be masked must be free of all dirt, oil or other contaminants. Cleaning is the most critical aspect of the masking procedure.
3. Apply XP-2000 to the area to be masked by dipping or brushing. For reducing XP-2000, use XP-2000 REDUCER only.
4. Apply a minimum of two coats depending upon the type of plating/chemical solution and/or length of pro cessing time in solution. Allow at least 30 minutes air-dry time between coats and overnight air-dry time after application of final coat before introduction into solution. Faster drying of XP-2000 can be accom plished by force drying for 15 minutes in an oven not exceeding 140_ F or over a hot plate not exceeding 140_ F for 15 minutes. Drying over a hot plate is preferable to oven drying. Drying time will vary according to relative humidity. NOTE: Make sure XP-2000 has lost all solvent odor before force drying or applying additional coats.
5. XP-2000 will not withstand extended periods in hot alkaline solutions. Two (2) minutes is the maximum time permitted.
6. XP-2000 can normally be peeled from the part after use if the part is warm. For mass stripping or removal from recessed areas, use: 1. XP-2000 Reducer; 2. Toluene; 3. Miccrostrip A. The first two are the fastest.
CHARACTERISTICS
Color:: Orange
Viscosity: 5000-6000 cps
Coverage Rate: Approx. 130 sq. ft. (12 m2) per gallon, 12 mli dry film.
WtlGal.: 7.90 Ibs./gal.
Flash Point: 24_ F. TCC
XP-2000 is available in: 1 gal., 5 gal., and 55 gal. containers.
PRECAUTIONARY INFORMATION
CONTAINS VOLATILE SOLVENTSKeep away from sparks and open flame. Store at temperatures above 32_ F and below 105_ F. Keep containers closed when not in use. Maintain adequate ventilation in working area. Wear approved respirators and protective clothing when working in confined areas. Avoid repeated breathing of concentrated vapors. Prolonged contact of liquid material with skin may be irritating. If material comes in contact with skin, wash skin surface thoroughly with soap and water. In case of eye contact, flush eyes thoroughly for 15 minutes with water and consult a physician. REFER TO MATERIAL SAFETY DATA SHEET FOR ADDITIONAL WARNINGS AND INFORMATION.
Other products in the category Chemicals for Special Applications / Plating:
Anodes Zinc Metal Balls 99%+ 50 Lb Box -- NEW CUSTOMERS (CALL, EMAIL or QUOTE) for PRICE
Antifoam(tm) 1410 40 Lb Pail -- NEW CUSTOMERS (CALL, EMAIL or QUOTE) for PRICE
Antifoam(tm) 1410 441 Lb Drum -- NEW CUSTOMERS (CALL, EMAIL or QUOTE) for PRICE
Cadmium Oxide Technical Grade 50 Lbs Pail HAZMAT -- NEW CUSTOMERS (CALL, EMAIL or QUOTE) for PRICE
Chrome Etch Type 1020 1Gal Bottle HAZMAT C51020 -- NEW CUSTOMERS (CALL, EMAIL or QUOTE) for PRICE
MICCRO SH-110 VOC FREE 1 Gal Can
MICCRO SUPER XP-2000 STOP-OFF LACQUER 5 Gal Can
MICCROMASK STOP-OFF LACQUER 1 Gal Can
MICCROMASK STOP-OFF LACQUER 5 Gal Can
MICCROPATCH MC-753 AIR DRY PATCH FOR PLASTISOL COATINGS BLACK 1 Gal Can
MICCROPATCH MC-753 AIR DRY PATCH FOR PLASTISOL COATINGS BLACK 5 Gal Can
MICCROPEEL LACQUER 1 Gal Can
MICCROSHIELD STOP-OFF LACQUER 1 GAL Can GCI# MS5901 Tolber HAZMAT
MICCROSHIELD STOP-OFF LACQUER 5 Gal Can
MICCROSHIELD STOP-PEEL REDUCER 1 Gal Can
MICCROSHIELD STOP-PEEL REDUCER 5 Gal Can
MICCROSTOP STOP-OFF LACQUER 5 Gal Can
MICCROSTOP STOP-OFF LACQUER (1 Gal Can) M59012 Tolber HAZMAT
MICCROSTRIP "A" 1 Gal Can
MICCROSTRIP "A" 5 Gal Can
MICCROTAPE # 1210, 1in 1 Each Roll
MICCROTAPE 3/4" BLACK 1 Each Roll HAZMAT
MICCROTAPE CEMENT 1 Gal Can
MICCROTEX LACQUER 1 Gal Can
MICCROTEX/MICCROPATCH REDUCER 1 Gal Can
MICRO XP-2000 LR LACQUER 1 Gal Can
PLASTISOL BLACK 1 Gal Can -- Product Specs
PLASTISOL BLACK 5 Gal Can -- Product Specs
PLASTISOL ORANGE 1 Gal Can -- Product Specs
PLASTISOL ORANGE 5 Gal Can -- Product Specs
SUPER XP-2000 REDUCER 1 Gal Can
T-100 PLASTISOL PRIMER 1 Gal Can
T-100 PLASTISOL PRIMER 5 Gal Can
T-100 PLASTISOL PRIMER REDUCER 1 Gal Can -- Please reference Part # M59011 when ordering
T-100 PLASTISOL PRIMER REDUCER 5 Gal Can -- Please reference Part # M59111 when ordering
XP-420 LVOC L.R. 5 Gal Can
|
|
|||||||||||||
|
|||||||||||||